myhobby-cnc:grbl-controller
Unterschiede
Hier werden die Unterschiede zwischen zwei Versionen gezeigt.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
myhobby-cnc:grbl-controller [2016/07/15 09:29] crix [Grundkonfiguration] |
myhobby-cnc:grbl-controller [2019/07/03 13:19] crix |
||
|---|---|---|---|
| Zeile 24: | Zeile 24: | ||
| Die Konfiguration kann über die Kommando's **$$** (Anzeige der aktuellen Konfigurationsparameter) und **$x=y** (Parameter x auf Wert y einstellen) jedoch manuell vorgenommen werden. | Die Konfiguration kann über die Kommando's **$$** (Anzeige der aktuellen Konfigurationsparameter) und **$x=y** (Parameter x auf Wert y einstellen) jedoch manuell vorgenommen werden. | ||
| - | {{:myhobby-cnc:grbl-controller-config.jpg |}} | + | **GRBL 0.8c Konfiguration** |
| - | GRBL 0.8c Konfiguration. Passende Parameter für GRBL 0.9 sind weiter unten verlinkt. | + | |
| + | <code> | ||
| + | $0=33.333 (x, step/mm) | ||
| + | $1=33.333 (y, step/mm) | ||
| + | $2=320.000 (z, step/mm) | ||
| + | $3=10 (step pulse, usec) | ||
| + | $4=250 (Default feed, mm/min) | ||
| + | $5=500 (Default seek, mm/min) | ||
| + | $6=0 (step port invert mask:00000000) | ||
| + | $7=25 (step idle delay, msec) | ||
| + | $8=25 (acceleration, mm/sec^2) | ||
| + | $9=0.010 (junction deviation, mm) | ||
| + | $10=0.002 (arc tolerance, mm) | ||
| + | $11=25 (n-arc correction, int) | ||
| + | $12=3 (n-decimals, int) | ||
| + | $13=0 (report inches, bool) | ||
| + | $14=1 (auto start, bool) | ||
| + | $15=0 (invert step enable, bool) | ||
| + | $16=0 (hard limits, bool) | ||
| + | $17=0 (homing cycle, bool) | ||
| + | $18=0 (homing dir invert mask:00000000) | ||
| + | $19=25.000 (homing feed, mm/min) | ||
| + | $20=700.000 (homing seek, mm/min) | ||
| + | $21=250 (homing debounce, msec) | ||
| + | $22=1.000 (homing pull-off, mm) | ||
| + | </code> | ||
| + | |||
| + | **GRBL 0.9 - 1.1 Konfiguration** | ||
| + | |||
| + | <code> | ||
| + | $0=10 (step pulse, usec) | ||
| + | $1=25 (step idle delay, msec) | ||
| + | $2=0 (step port invert mask:00000000) | ||
| + | $3=0 (dir port invert mask:00000000) | ||
| + | $4=0 (step enable invert, bool) | ||
| + | $5=0 (limit pins invert, bool) | ||
| + | $6=0 (probe pin invert, bool) | ||
| + | $10=3 (status report mask:00000011) | ||
| + | $11=0.010 (junction deviation, mm) | ||
| + | $12=0.002 (arc tolerance, mm) | ||
| + | $13=0 (report inches, bool) | ||
| + | $20=0 (soft limits, bool) | ||
| + | $21=0 (hard limits, bool) | ||
| + | $22=0 (homing cycle, bool) | ||
| + | $23=0 (homing dir invert mask:00000000) | ||
| + | $24=25.000 (homing feed, mm/min) | ||
| + | $25=700.000 (homing seek, mm/min) | ||
| + | $26=250 (homing debounce, msec) | ||
| + | $27=1.000 (homing pull-off, mm) | ||
| + | $100=33.333 (x, step/mm) | ||
| + | $101=33.333 (y, step/mm) | ||
| + | $102=320.000 (z, step/mm) | ||
| + | $110=4000.000 (x max rate, mm/min) | ||
| + | $111=4000.000 (y max rate, mm/min) | ||
| + | $112=1000.000 (z max rate, mm/min) | ||
| + | $120=25.000 (x accel, mm/sec^2) | ||
| + | $121=25.000 (y accel, mm/sec^2) | ||
| + | $122=10.000 (z accel, mm/sec^2) | ||
| + | $130=200.000 (x max travel, mm) | ||
| + | $131=200.000 (y max travel, mm) | ||
| + | $132=200.000 (z max travel, mm) | ||
| + | </code> | ||
| ====Weitere Konfigurationen==== | ====Weitere Konfigurationen==== | ||
| Eine komplette Beschreibung aller Konfigurationsparameter für die GRBL v0.9 kann man unter folgendem Link finden: | Eine komplette Beschreibung aller Konfigurationsparameter für die GRBL v0.9 kann man unter folgendem Link finden: | ||
myhobby-cnc/grbl-controller.txt · Zuletzt geändert: 2020/04/16 22:03 von crix
Seiten-Werkzeuge
